Lull 944E-42 Service Manual Manuel d'utilisateur Page 134
- Page / 266
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Hydraulic System
8-18
944E-42
5. Thoroughly clean the main control valve and
surrounding area, including all hoses and fittings,
before proceeding.
6. Label, disconnect and cap all hydraulic hoses
attached to the main control valve, accumulator
charge/secondary function valve and the pilot select
valve. Place a suitable container to catch hydraulic
fluid drainage from beneath the cab.
7. Remove the step assembly from the side of the cab.
Refer to Section 4.5, “Cab Removal.”
8. Check to make sure the two tethers (1) are
positioned in the two mounting tabs (2) on the front
and rear sides of the cab mount. If not, place the
loop of the tether in the mount before proceeding.
9. Place a floor jack under the outer edge of the sub
plate (3) to hold the sub plate in position while
removing the two cap screws (4) and washers
securing the sub plate to the cab support.
10. Remove the cap screws and slowly lower the sub
plate down until the sub plate is supported by the
two tethers mounted on the cab support.
b. Sub Plate with Valve Plate Removal
Refer to Section 4.5, “Cab Removal,” for sub plate
removal procedure and reassembly procedure.
8.7.2 Main Control Valve
The main control valve assembly (5) consists of various
working sections with their own valve assemblies, each
providing a specific hydraulic function. The section
assemblies are the inlet (6), transfer carriage spool
section (7), auxiliary section (8) and the four spool mono
block section (9).
If service to the main control valve assembly is required,
swing the sub plate, with valve plate assembly, down to
gain access to the valve and fittings. Refer to Section
8.7.1, “Valve Plate Assembly.”
a. Main Control Valve Removal from Valve Plate
Before disassembling the main control valve, remove it
from the valve plate assembly. Label and remove all the
hoses from the fittings. Cap and plug all hose ends and
fittings.
1. Wipe up any hydraulic fluid spillage in, on, near and
around the machine and work area.
2. Secure the main control valve in place on the valve
plate to prevent sudden movement when the
hardware is removed.
WARNING
ALWAYS support the sub plate before loosening or
removing any mounting hardware.
MU3822
1
2
3
4
MU3861
6
8
5
7
9
MU3871
10
10
- Service Manual 1
- EFFECTIVITY PAGE 3
- SECTION CONTENTS 5
- Section Subject Page 6
- Section 1 9
- Safety Practices 9
- 1.1 INTRODUCTION 10
- 1.2 DISCLAIMER 10
- 1.4 DO NOT OPERATE TAGS 10
- 1.5 SAFETY INFORMATION 10
- 1.6 SAFETY INSTRUCTIONS 11
- 1.7 SAFETY DECALS 12
- Section 2 13
- 2.1 REPLACEMENT PARTS AND 14
- WARRANTY INFORMATION 14
- 2.2 TORQUE CHARTS 15
- (Continued) 16
- SOCKET HEAD CAP SCREWS 17
- CLASS 8.8 METRIC BOLTS 19
- CLASS 8 METRIC NUTS 19
- Magni Coating* 21
- 2.3 SPECIFICATIONS 23
- 2.3.5 Tires 24
- 2.5 SERVICE AND MAINTENANCE 27
- SCHEDULES 27
- LB/FT (Nm) 28
- 2.6 LUBRICATION SCHEDULES 30
- Section 3 31
- 3.1 BOOM SYSTEM COMPONENT 32
- 3.2 BOOM SYSTEM 33
- BOOM EXTEND AND RETRACT 44
- 3.4.2 Inspection Guidelines 45
- 3.4.4 Chain Lubrication 47
- 3.5 BOOM WEAR PADS 52
- 3.6 QUICK ATTACH ASSEMBLY 53
- 3.7 FORKS 53
- 3.8 TROUBLESHOOTING 54
- 3.9 EMERGENCY BOOM LOWERING 57
- Section 4 61
- Cab and Covers 61
- 4.2 OPERATOR’S CAB 63
- 4.3 CAB COMPONENTS 63
- 4.3.2 Steer Select Valve 64
- 4.3.4 Throttle Pedal 65
- 4.3.6 Joystick Assemblies 67
- 4.4 ENCLOSED CAB (OPTIONAL) 68
- COMPONENTS 68
- 4.5 CAB REMOVAL 69
- 4.6 CAB INSTALLATION 71
- 4.7 VALVE PLATE 72
- Section 5 73
- 5.2 GENERAL INFORMATION 75
- 5.3 AXLE ASSEMBLIES 75
- 5.3.5 Axle Replacement 76
- 5.3.6 Axle Installation 77
- To Transmission 82
- 5.5 WHEELS AND TIRES 83
- Tread “arrows” must point 84
- Install tires onto wheels to 84
- 5.7 TOWING A DISABLED MACHINE 85
- Section 6 87
- 6.1 TRANSMISSION ASSEMBLY 88
- AND MAINTENANCE INFORMATION 89
- 6.4 TRANSMISSION REPLACEMENT 89
- 6.5 TROUBLESHOOTING 93
- 6.6 TRANSFER CASE COMPONENT 97
- 6.7 TRANSFER CASE 98
- 6.9 TRANSFER CASE MAINTENANCE 98
- 6.10.1 Transfer Case Removal 99
- 6.11 TROUBLESHOOTING 100
- Problem Cause Remedy 100
- Transmission 102
- Section 7 103
- 7.1.1 Disclaimer and Scope 104
- 7.1.2 Component Terminology 105
- 7.2 ENGINE SERIAL NUMBER 106
- 7.3 SPECIFICATIONS AND 106
- MAINTENANCE INFORMATION 106
- 7.4 ENGINE COOLING SYSTEM 106
- 7.5 ENGINE ELECTRICAL SYSTEM 107
- 7.6 FUEL SYSTEM 107
- 7.7 ENGINE EXHAUST SYSTEM 109
- 7.8 AIR CLEANER ASSEMBLY 110
- 7.9 ENGINE REPLACEMENT 111
- 7.9.2 Engine Installation 113
- 7.10 TROUBLESHOOTING 115
- Section 8 117
- Hydraulic System 117
- 8.1 HYDRAULIC COMPONENT 118
- TERMINOLOGY 118
- 8.2 SAFETY INFORMATION 119
- 8.4 HYDRAULIC CIRCUITS 121
- Hydraulic Pump Flow Test 123
- DUAL JOYSTICK CONFIGURATION 128
- 8.5 HYDRAULIC RESERVOIR 129
- 8.6 HYDRAULIC SYSTEM PUMP 132
- 8.7 VALVES AND MANIFOLDS 133
- 8.7.2 Main Control Valve 134
- 8.7.9 Service Brake Valve 144
- 8.7.10 Brake Test 145
- 8.7.11 Power Steering Valve 145
- 8.7.12 Steer Select Valve 146
- Function Valve 148
- 8.7.14 Accumulators 149
- 8.7.15 General Information 150
- 8.7.16 Checking Pre-Charge 152
- 8.8 HYDRAULIC CYLINDERS 154
- AFTER the head gland 155
- AXLE CENTER SECTION 156
- STEERING CYLINDER 156
- Section 9 159
- Electrical System 159
- 9.1 ELECTRICAL COMPONENT 161
- 9.2 SPECIFICATIONS 162
- 9.3 SAFETY INFORMATION 162
- 9.4 FUSES AND RELAYS 162
- 9.5 ELECTRICAL SCHEMATICS 164
- CHASSIS CIRCUIT 170
- AUXILIARY HYDRAULICS 170
- ENCLOSED CAB OPTION 170
- 9.7 ENGINE START CIRCUIT 172
- 9.8 CHARGING CIRCUIT 173
- 9.9 WINDOW WIPER/WASHER 174
- WINDSHIELD WIPER MOTOR 174
- 9.9.2 Skylight Wiper Motor 175
- 9.9.3 Rear Wiper Switch/Motor 176
- 9.10 CAB HEATER AND FAN 178
- 9.11 SWITCHES AND SOLENOIDS 179
- PARK BRAKE INDICATOR 181
- 9.11.9 Dual Joystick 185
- 9.11.11 Boom Angle Sensor 188
- 9.11.15 Hourmeter 191
- 9.12 DASH SWITCHES 194
- 9.13 TROUBLESHOOTING 195
- Multimeter (DMM) 208
- Section 10 213
- Stabil-TRAK™ System 213
- 10.1 STABIL-TRAK™ SYSTEM 214
- COMPONENT TERMINOLOGY 214
- 10.2 STABIL-TRAK™ DESCRIPTION 215
- 10.4 STABIL-TRAK™ SYSTEM TEST 222
- Locked Mode, Frame Sway Right 235
- Section 11 241
- Transfer Carriage 241
- 11.2 TRANSFER CARRIAGE 243
- 11.3 TRANSFER CARRIAGE 243
- MAINTENANCE 243
- 11.3.3 Rear Wear Pad Check 249
- 11.3.4 Rear Wear Pad Shimming 250
- 11.3.10 Rear Roller Gap Check 252
- 11.3.11 Rear Roller Shimming 253
- 11.3.13 Front Roller Shimming 255
- Replacement 256
- 11.4 TROUBLESHOOTING 262
- 31200355 266
© 2020, manymanuals.fr. Tous droits réservés | 0.850 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels